Low Profile Carrier V1 MultiCam
The LPC features our new air vent thermo pads, which allows heat to evaporate from the body and increase the airflow to assist in cooling. The Thermo Pad also helps to decrease the back plate signature associated with ballistic trauma.The LPC utilises state of the art materials to reduce the overall signature and weight. It comes as standard with a removable MOLLE front flap held in place by 2 vertical QASM clips and hook and loop which allows the panel to be removed and replaced with a wide variety of preconfigured panels that are both weapon and mission specific.
The LPC incorporates our speed clip system, which allows very rapid removal of the carrier on a day to day basis, but also in an emergency situation, no complicated cables to worry about, and reassembly takes seconds.
Size Medium: Will fit up to a size 45" (114cm) chest.
Size Large: Will fit Chest sizes 45" (114cm) to 52" (132cm)
The carrier holds 25cm x 30cm (10" x 12") stand alone plates front and back, 15cm x 15cm (6" x 6"), and 15cm x 20cm (6" x 8") side plates and soft armour.
Low Profile Carrier V2 MultiCam
The LPC features our new air vent thermo pads, which allows heat to evaporate from the body and increase the airflow to assist in cooling. The Thermo Pad also helps to decrease the back plate signature associated with ballistic trauma.The LPC utilises state of the art materials to reduce the overall signature and weight. It comes as standard with a removable MOLLE front flap held in place by 2 vertical QASM clips and hook and loop which allows the panel to be removed and replaced with a wide variety of preconfigured panels that are both weapon and mission specific.
The LPC incorporates our speed clip system, which allows very rapid removal of the carrier on a day to day basis, but also in an emergency situation, no complicated cables to worry about, and reassembly takes seconds.
Size Medium: Will fit up to a size 45" (114cm) chest.
Size Large: Will fit Chest sizes 45" (114cm) to 52" (132cm)
The carrier holds 25cm x 30cm (10" x 12") stand alone plates front and back, 15cm x 15cm (6" x 6"), and 15cm x 20cm (6" x 8") side plates and soft armour.
Low Profile Carrier V1 Ranger Green
The LPC features our new air vent thermo pads, which allows heat to evaporate from the body and increase the airflow to assist in cooling. The Thermo Pad also helps to decrease the back plate signature associated with ballistic trauma.The LPC utilises state of the art materials to reduce the overall signature and weight. It comes as standard with a removable MOLLE front flap held in place by 2 vertical QASM clips and hook and loop which allows the panel to be removed and replaced with a wide variety of preconfigured panels that are both weapon and mission specific.
The LPC incorporates our speed clip system, which allows very rapid removal of the carrier on a day to day basis, but also in an emergency situation, no complicated cables to worry about, and reassembly takes seconds.
Size Medium: Will fit up to a size 45" (114cm) chest.
Size Large: Will fit Chest sizes 45" (114cm) to 52" (132cm)
The carrier holds 25cm x 30cm (10" x 12") stand alone plates front and back, 15cm x 15cm (6" x 6"), and 15cm x 20cm (6" x 8") side plates and soft armour.
Low Profile Carrier V2 Ranger Green
The LPC features our new air vent thermo pads, which allows heat to evaporate from the body and increase the airflow to assist in cooling. The Thermo Pad also helps to decrease the back plate signature associated with ballistic trauma.The LPC utilises state of the art materials to reduce the overall signature and weight. It comes as standard with a removable MOLLE front flap held in place by 2 vertical QASM clips and hook and loop which allows the panel to be removed and replaced with a wide variety of preconfigured panels that are both weapon and mission specific.
The LPC incorporates our speed clip system, which allows very rapid removal of the carrier on a day to day basis, but also in an emergency situation, no complicated cables to worry about, and reassembly takes seconds.
Size Medium: Will fit up to a size 45" (114cm) chest.
Size Large: Will fit Chest sizes 45" (114cm) to 52" (132cm)
The carrier holds 25cm x 30cm (10" x 12") stand alone plates front and back, 15cm x 15cm (6" x 6"), and 15cm x 20cm (6" x 8") side plates and soft armour.
Recon Plate Carrier MK1 Combo Black
The RPC comes as standard with a removable MOLLE front flap held in place by 2 vertical SQM clips and strong velcro which allows the panel to be removed and replaced with a wide variety of preconfigured weapon-specific pouch panels and Warrior’s new Pathfinder Chest Rig. The RPC integrates with Warrior's new Back PanelPathfinder Chest Rig W-EO-PCRThe PCR is the latest edition to the Warrior Assault Systems product line. Designed to work as a compact Chest Rig in stand-alone configuration or in conjunction with Warrior's new Recon Plate Carrier System (RPC).
The PCR accommodates 4 x M4 style mags with adjustable bungee retention which allows AK mags to be easily changed out. There are 2 x small utility pouches. One at either side with elastic loops for storage of chem-lights small torches etc. The front section comes as standard with Warriors Double Elastic Low Profile Mag pouches these are attached with MOLLE and can be easily changed out for any of Warriors full range of pouches such as our DPDA Double Pistol Mag pouch.The unique feature of the PCR is its ability to attach to Warrior's new RPC plate carrier. Simply remove the shoulder and rear straps and all the remaining clips line up with the corresponding ITW clips located on the front and sides of the RPC Plate carrier creating a scalable armour platform for low and high vis operations.Made from genuine US Mil Spec materials and hardware.
DCS Releasable Plate Carrier – MultiCam
2 x side cummerbunds allow ambidextrous opening and closure via Mil Spec Velcro sewn on the lower front of the carrier and sandwiched under a front panel. The front panel has 3 vertical MOLLE rows and 6 horizontal MOLLE loops which allow direct attachment of immediately accessible items such as magazine pouches. Thumb loops in 1 inch webbing greatly expedite the upward movement of the front panel to allow either cummerbund to be opened.The internal walls of the carrier have a 3/8s inch 3D Spacer mesh lining that allows heat from the body to evaporate this coupled with its ability to allow air flow to pass through the mesh results in an excellent cooling effect. The 3D Spacer mesh has positive compression features that greatly enhances the operator's comfort levels. The shoulder sections of the carrier are comprised of double layered 2 inch Mil Spec Camo webbing and are covered with removable padded sleeves which help to spread the weight of the carriers load on the operators shoulders the sleeves can also be opened to allow communication cables and hydration tubes to be routed through.
The rear of the carrier has a 2 inch matched camo reinforced Man Down drag handle for extraction of casualties.
The carrier is fully releasable should the user need to rapidly remove the carrier in an emergency situation for example if he falls into water or if a medic needs to treat a serious trauma injury. The carrier incorporates an internal cable system featuring an ambidextrous release pull. The release pull is securely located in the shoulder and allows a smooth rapid separation of the front back and sides of the carrier into individual components. The carrier is fully adjustable for size on the shoulder and girth.All Threads are Type 69 Nylon Bonded construction which are resistant to mildew the effects of UV light and degradation form water heat and cold.
DCS Releasable Plate Carrier – Black
2 x side cummerbunds allow ambidextrous opening and closure via Mil Spec Velcro sewn on the lower front of the carrier and sandwiched under a front panel. The front panel has 3 vertical MOLLE rows and 6 horizontal MOLLE loops which allow direct attachment of immediately accessible items such as magazine pouches. Thumb loops in 1 inch webbing greatly expedite the upward movement of the front panel to allow either cummerbund to be opened.The internal walls of the carrier have a 3/8s inch 3D Spacer mesh lining that allows heat from the body to evaporate this coupled with its ability to allow air flow to pass through the mesh results in an excellent cooling effect. The 3D Spacer mesh has positive compression features that greatly enhances the operator's comfort levels. The shoulder sections of the carrier are comprised of double layered 2 inch Mil Spec Camo webbing and are covered with removable padded sleeves which help to spread the weight of the carriers load on the operators shoulders the sleeves can also be opened to allow communication cables and hydration tubes to be routed through.
The rear of the carrier has a 2 inch matched camo reinforced Man Down drag handle for extraction of casualties.
The carrier is fully releasable should the user need to rapidly remove the carrier in an emergency situation for example if he falls into water or if a medic needs to treat a serious trauma injury. The carrier incorporates an internal cable system featuring an ambidextrous release pull. The release pull is securely located in the shoulder and allows a smooth rapid separation of the front back and sides of the carrier into individual components. The carrier is fully adjustable for size on the shoulder and girth.All Threads are Type 69 Nylon Bonded construction which are resistant to mildew the effects of UV light and degradation form water heat and cold.
DCS Releasable Plate Carrier – Coyote Tan
2 x side cummerbunds allow ambidextrous opening and closure via Mil Spec Velcro sewn on the lower front of the carrier and sandwiched under a front panel. The front panel has 3 vertical MOLLE rows and 6 horizontal MOLLE loops which allow direct attachment of immediately accessible items such as magazine pouches. Thumb loops in 1 inch webbing greatly expedite the upward movement of the front panel to allow either cummerbund to be opened.The internal walls of the carrier have a 3/8s inch 3D Spacer mesh lining that allows heat from the body to evaporate this coupled with its ability to allow air flow to pass through the mesh results in an excellent cooling effect. The 3D Spacer mesh has positive compression features that greatly enhances the operator's comfort levels. The shoulder sections of the carrier are comprised of double layered 2 inch Mil Spec Camo webbing and are covered with removable padded sleeves which help to spread the weight of the carriers load on the operators shoulders the sleeves can also be opened to allow communication cables and hydration tubes to be routed through.
The rear of the carrier has a 2 inch matched camo reinforced Man Down drag handle for extraction of casualties.
The carrier is fully releasable should the user need to rapidly remove the carrier in an emergency situation for example if he falls into water or if a medic needs to treat a serious trauma injury. The carrier incorporates an internal cable system featuring an ambidextrous release pull. The release pull is securely located in the shoulder and allows a smooth rapid separation of the front back and sides of the carrier into individual components. The carrier is fully adjustable for size on the shoulder and girth.All Threads are Type 69 Nylon Bonded construction which are resistant to mildew the effects of UV light and degradation form water heat and cold.
Recon Plate Carrier MK1 Combo MultiCam
The RPC comes as standard with a removable MOLLE front flap held in place by 2 vertical SQM clips and strong velcro which allows the panel to be removed and replaced with a wide variety of preconfigured weapon-specific pouch panels and Warrior’s new Pathfinder Chest Rig. The RPC integrates with Warrior's new Back PanelPathfinder Chest Rig W-EO-PCRThe PCR is the latest edition to the Warrior Assault Systems product line. Designed to work as a compact Chest Rig in stand-alone configuration or in conjunction with Warrior's new Recon Plate Carrier System (RPC).
The PCR accommodates 4 x M4 style mags with adjustable bungee retention which allows AK mags to be easily changed out. There are 2 x small utility pouches. One at either side with elastic loops for storage of chem-lights small torches etc. The front section comes as standard with Warriors Double Elastic Low Profile Mag pouches these are attached with MOLLE and can be easily changed out for any of Warriors full range of pouches such as our DPDA Double Pistol Mag pouch.The unique feature of the PCR is its ability to attach to Warrior's new RPC plate carrier. Simply remove the shoulder and rear straps and all the remaining clips line up with the corresponding ITW clips located on the front and sides of the RPC Plate carrier creating a scalable armour platform for low and high vis operations.Made from genuine US Mil Spec materials and hardware.