DCS Releasable Plate Carrier – MultiCam W-EO-DCS-R-L-MC (Large)
2 x side cummerbunds allow ambidextrous opening and closure via Mil Spec Velcro sewn on the lower front of the carrier and sandwiched under a front panel. The front panel has 3 vertical MOLLE rows and 6 horizontal MOLLE loops which allow direct attachment of immediately accessible items such as magazine pouches. Thumb loops in 1 inch webbing greatly expedite the upward movement of the front panel to allow either cummerbund to be opened.
The internal walls of the carrier have a 3/8s inch 3D Spacer mesh lining that allows heat from the body to evaporate this coupled with its ability to allow air flow to pass through the mesh results in an excellent cooling effect. The 3D Spacer mesh has positive compression features that greatly enhances the operator’s comfort levels. The shoulder sections of the carrier are comprised of double layered 2 inch Mil Spec Camo webbing and are covered with removable padded sleeves which help to spread the weight of the carriers load on the operators shoulders the sleeves can also be opened to allow communication cables and hydration tubes to be routed through.
The rear of the carrier has a 2 inch matched camo reinforced Man Down drag handle for extraction of casualties.
The carrier is fully releasable should the user need to rapidly remove the carrier in an emergency situation for example if he falls into water or if a medic needs to treat a serious trauma injury. The carrier incorporates an internal cable system featuring an ambidextrous release pull. The release pull is securely located in the shoulder and allows a smooth rapid separation of the front back and sides of the carrier into individual components. The carrier is fully adjustable for size on the shoulder and girth.
All Threads are Type 69 Nylon Bonded construction which are resistant to mildew the effects of UV light and degradation form water heat and cold.
Stand alone plates, 250mm x 300mm (10" x 12")and SAPI 238mm x 314mm (9.5" x 12.5")
ICW plates 250mm x 300mm and SAPI 238mm x 314mm, with Nexus NIJ 3a soft armour.
All Warrior lightweight plate carriers are designed to work with Nexus style SAPI shaped 10" x 12" ( 250mm + x 300mm + ) ballistic plates including bevelled edge ceramic plates and smooth edge composite plates. Steel plates with hard edges and corners should be wrapped to protect the internals of the carriers to avoid excessive wear. Warrior Assault Systems will not be held responsible for any damage to a plate carrier from misuse as stated above.
NIJ Level 3a soft armour
High Quality Threads
Thread quality is fundamental to the construction, durability and strength of tactical equipment.
Two factors have a negative impact on the life Span of threads
1) Mildew is one of the most common factors in the deterioration of military kit, causing it to rot and ultimately results in unacceptable failure.
2) Sunlight has a harmful effect on the performance of threads, and over time causes their deterioration.
Warrior only uses the highest quality US Mil Spec nylon threads imported from the USA which are threated against both UV and Mildew.
- Fiber Resistance to Acid - Good
- Fiber Resistance to Alkali - Good
- Fiber Abrasion Resistance - Excellent
- Fiber Resistance to Heat - 142 deg C (Highest continuous temperature before breakdown)
- Fiber Melting Point - 265 deg C
MIL SPEC Fabric
500D Nylon fabric feature enhanced tear and abrasion resistance, and long lasting durability, 500D Nylon fabric made with solution dyed yarns are inherently stain resistant and easy to clean. MultiCam, Coyote Tan, Ranger Green, Black and A-TACS FG fabrics are all I.R Treated for the lowest signature.
Warrior only uses the highest quality Military rated Clips and accessories.
This product contains MOLLE webbing that will allow you to attach other pouches using the MOLLE system.
- Genuine US Mil Spec Webbing
- 25mm (1 Inch ) Breaking Strain: 1200 lbs
- 38mm (1.5 Inch ) Breaking Strain: 1800 lbs
- 50mm (2 Inch ) ) Breaking Strain: 2200 lbs